How to Install the Quick-Release Push-Button Lock for the Window Guard

Attach the Strike Pin to your window guard

The Strike Pin (3) should be permanently mounted on or around the outer alloy framing from the window guard -referred in order to from now in as WG- privately of the WG’s “door” opposite associated with the hinge, around the middle (the same place where a doorknob is positioned over a door). It should extend facing outward from the WOHNGEMEINSCHAFT toward the wall structure, so that this will later go into the Secure Box tip-first whenever closed.

IMPORTANT: Typically the Strike Pin should point straight as you possibly can, ie not directed slightly up, straight down, to the left, or to the correct. The straighter it truly is, the smoother its operation later.

The rear of the Hit Pin has strings to get a 1/4″ sl?, so a commonplace way of attaching the strike green to your WOHNGEMEINSCHAFT through first attaching a 1/4″ bolt it, then screwing the Strike Flag into that. Continue to, you don’t need to want individuals having the capacity to simply unscrew the bolt from the outside, so it is important that a person permanently correct it in order to the WG. It is most often performed by spot welding the attached Hit Pin set up, yet if a welder isn’t handy, in whatever way the bolt may be made unturnable will continue to work, such as working with one-way bolts.

Mount the Window Shield

Whether it isn’t previously, it’s time to be able to mount the WOHNGRUPPE on your home window. Attach the Locking mechanism Box (1) towards the end of your current pin so that it locks in place. If it is just not, be sure it is usually unlocked first by simply pushing the final involving the Push Pole (2) into typically the smaller hole involving the Lock Container first. This Lock Field will be mounted to the outer wall of your current building, so that you require to install typically the WG in a new position where the Fasten Box may be mounted using the top and bottom twist holes, and may not be pryed off (such as when it sits off the particular edge of your windows frame).

Another factor to keep within mind the following is of which there will always be an approximately 1/2″ hole drilled via your wall placed in the middle of the Freeze Box, and on the inside of the building, a a single 5/8″ diameter Flange will mount to the wall all-around that hole. When you put upwards the WG, you want the Fastener Box to always be close to the window beginning, but far enough allowing for this 1/2″ hole to be drilled from the wall structure, and hopefully end up being clear of virtually any inner wall interferences (like inside framing) for a a single 5/8″ diameter around the hole centre.

Mark your opening

With the Strike Pin attached to be able to your WG, plus the WG linked to your building, the remainder is relatively simple!

Now we require to mark where hole will always be drilled through the wall in order that it suits the small opening on the back again of the Fasten Box. First, push the Push Fishing rod (2) into the Fasten Box hole as a result it releases from the Strike Pin, plus remove it. Spot the Cardboard Go (4) all the way on the Strike Pin number, and stop the particular end with a knife so the particular cardboard only scarcely extends beyond the Strike Pin. Near the WG door slowly before the group of cardboard complies with the wall, then use a pad to draw a new circle where it lands.

Drill

Technically a 3/8″ exercise bit will be not too young for the particular Push Rod to be able to fit into, nevertheless I recommend a 1/2″ bit, which leaves more room for error, and even is covered upwards just fine. Utilizing the circle you merely marked, drill the hole straight via your building wall structure until you break the rules of the other side.

At this specific point, reattach the particular Lock Box to the WG and carry it closed. A person from the inside of should be ready to put their particular eye through the fresh drilled hole plus see the TOTAL small hole of the Lock Box. If it is usually partially covered, drill down the actual hole till there are a clear way to it.

Attach the Lock Box

If it is not already, reattach typically the Lock Box to the WG and keep it closed. Indicate the upper and even lower holes regarding the Lock Container with your trustworthy pencil, then wide open the WG and even drill them using the drill bit (NOT the large one! ) of which matches the screws you’re going to be able to use to attach the Lock Package, which don’t include the kit. These kinds of screws should end up being between 1/4″ and 3/8″, and need to be about 2″ to 3″ extended.

With your 2 holes drilled previously mentioned and below your own BIG one, eliminate the Lock Box in the WG (you recognize how by now, appropriate? ), place this on the walls, and mount this with your many of the. Screw them within until they’re comfortable, smaller completely make tighter just yet.

Align the Lock Box

Little by little close the WG female mounted Locking mechanism Box, being very careful Never to lock it in place. What’s of which? You say typically the Strike Pin isn’t lining up? Have a chill pill, Now i’m getting there.

Along with your hammer, smack the Lock Box sufficient to move that within the direction it needs to go. In the event that it won’t move, you screwed that in a tad too tight plus will need to loosen it. When it is lined up properly, you may well lock it in place to make sure this works. It can be unlocked, involving course, by adhering the Push Rod (2) through the hole in typically the wall until it finally releases. Note that you may want to “fish” around to the smaller hole within the Lock Box to enhance it in most the way.

push button box If everything is lined up, tighten typically the Lock Box screws all the approach. If everything is well aligned, typically the Push Rod need to easily open the WG along with the WG should easily lock in place. Despite the screws are usually tightened, you may possibly be in a position to employ the hammer intended for final adjustments.